







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Fairview, TX: What It Costs and How Fast It Goes In
A chain link fence in Fairview, TX usually runs $3,500 to $9,000, and most residential lots are finished in two to four working days once materials land on site. That range covers a standard 4-foot or 5-foot galvanized run with posts set in concrete, a walk gate, and a drive gate, depending on linear footage and terrain. Chain link isn’t the glamour pick on a wooded acre lot, but it’s the fastest, cheapest way to contain a dog, mark a property line, or secure a build site. Call (844) 560-0925 for a free on-site estimate.

How a Chain Link Fence Goes In, Stage by Stage

Chain link is a short job, but the sequence matters more than people expect. Get the layout wrong and you’ll be pulling posts out of blackland clay two weeks later. Here’s the actual order of operations we follow on a Fairview job.
- Stage 1: Layout and utility locate (day 1, half a day). We walk the line with you, confirm corners, gates and terminal posts, then call in the 811 locate so nobody drives a post through an irrigation line or a buried conduit. On acreage lots the line is often longer than the homeowner estimated, so this is your first decision point: exact boundary vs. a set-back line you prefer.
- Stage 2: Digging and setting posts (day 1 into day 2). Terminal, corner and gate posts get set in concrete and cured overnight. Line posts go in on the same pass. Fairview’s expansive clay means hole depth and concrete volume aren’t negotiable – we go deeper than the minimum on gate posts because frost heave isn’t the issue here, soil movement is.
- Stage 3: Top rail, tension wire and mesh (day 2 into day 3). We stretch the mesh tight along the top rail or tension wire, depending on height and spec. This is where you choose height and whether you want a top rail or a tension-wire bottom configuration.
- Stage 4: Gates and hardware (day 3). Walk gates and drive gates hang, latch and swing. If you’re adding a drive gate for a trailer or RV pad, confirm the opening width now – widening it later means new posts.
- Stage 5: Walkthrough and cleanup (day 3 into day 4). We tension-check, confirm latches, haul off spoils and leave you a clean line. You sign off, and the 730-Day Done Right Promise covers the workmanship from there.
Two to four days is the norm. A long perimeter around a one-acre-plus lot, or a run that has to thread between mature trees, can push to a week.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Options You’ll Actually Choose Between
Chain link isn’t one product. The choices below are the ones that change both the price and how the fence looks and holds up in Fairview.
- Height: 4 ft vs. 5 ft vs. 6 ft. Four-foot is the budget pick for pet containment and line marking. Five-foot is the sweet spot for most residential lots. Six-foot costs more per foot but reads as more secure and is the common choice where a pool or shop building needs screening.
- Coating: galvanized vs. vinyl-coated. Bare galvanized is the cheapest and holds up fine in North Texas, but it goes dull gray. Vinyl-coated (usually black or green) costs maybe 15-25% more and blends into trees and landscaping far better – a real consideration on a wooded Fairview lot where the fence line runs through the tree canopy.
- Gauge and mesh size. Standard residential mesh is 11.5 or 12 gauge. Heavier 9-gauge is worth it if you’re containing a large dog or securing a build site. Smaller mesh openings cost more but keep small pets in.
- Top rail vs. tension wire. A top rail gives a cleaner, stiffer top line; tension wire is cheaper and lets the mesh flex at the top. For a straight run, top rail wins on looks.
- Gates. Walk gates are standard; drive gates for trailers or equipment add cost and need heavier posts. Decide gate widths before we set posts, not after.
What Chain Link Fence Costs in Fairview, TX

Most Fairview chain link fence jobs land between $3,500 and $9,000. Here’s what moves a job to the low or high end of that range.
- Linear footage. This is the biggest driver. A modest back-yard enclosure sits near the bottom; a full perimeter around a one-acre-plus lot pushes toward the top.
- Terrain and tree clearing. Fairview’s wooded acreage lots often need brush cleared and the line routed around mature trees and set-backs, which adds labor and time.
- Coating and gauge. Vinyl-coated and heavier gauge raise the per-foot number but hold up better.
- Gates. Each gate adds hardware, heavier posts and labor. Drive gates are the priciest.
- Permit and HOA scope. Some Fairview lots sit under HOA rules on fence height and color, and any permit or inspection adds cost. Materials availability can shift the number too – brands like CertainTeed and GAF come up when fencing ties into a broader exterior project, though chain link itself is a commodity product.
A written estimate should spell out footage, height, coating, gauge, gate count, post setting and cleanup. Ask what isn’t included – stump grinding, haul-off of old fence, and utility relocation are the usual exclusions.
See the difference
Before
After
Before
After
Before
AfterWhat Fairview Homes and Lots Do to This Job
Fairview is a small, affluent Collin County town where almost all construction is new custom-home building or major renovation on large wooded lots, not repair of older housing stock. Because the town is nearly built out, we spend as much time on tear-downs and lot-by-lot infill as on new subdivision work – and that shapes fencing here. On a one-acre-plus wooded lot, the fence line usually has to thread around mature trees and set-backs, so layout takes longer than on a tight suburban lot. North Texas blackland clay expands and shrinks with wet and dry cycles, so we go deeper on post holes and pay close attention to drainage grading; a fence that only looks right because the soil was wet when it went in is a callback waiting to happen. Fairview’s ZIP, 75002, covers lots where HOAs sometimes set height and color rules, so we confirm those before ordering material. If your chain link is part of a bigger exterior plan, our Fence Installation service covers the wider scope, and homeowners often pair this with ADU Site Prep & Utilities in Fairview when a lot is being developed.

Serving Fairview, TX – Our Local Coverage Area
We serve Fairview and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Chain Link Fence in Fairview

Most residential lots are done in two to four working days once materials are on site. Larger wooded lots or jobs with tree clearing can run a week. Call (844) 560-0925 for a timeline on your lot.
It depends on your lot and HOA. Some Fairview properties require a permit and inspection, and HOAs often set height and color rules. We confirm what applies to your address before work starts, and the estimate will state whether a permit is included. Call (844) 560-0925 with your address and we’ll sort out the requirements.
Yes, in most cases. We set posts on the line and route around mature trees and irrigation where possible, so disruption is limited to the post holes. If tree clearing is needed, that’s called out separately. Call (844) 560-0925 for a free site walk.
Most jobs run $3,500 to $9,000, with footage, coating, gauge, gates and tree clearing driving the number to the low or high end. You get a written, line-item estimate before anything is ordered. Call (844) 560-0925 for an exact quote – estimates are free.
Our workmanship is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. Materials carry their own manufacturer warranties. Call (844) 560-0925 to schedule your estimate.
Get a Free Chain Link Fence Estimate in Fairview
Ready to price a chain link fence in Fairview? Call (844) 560-0925 for a free on-site estimate. We walk the line with you, measure footage, confirm gates, check HOA and permit requirements for your address, and hand you a written figure with materials and labor spelled out. A live person answers, 24/7. If the fence is part of a full Fence Installation in Fairview plan, or you’re also tackling Door Installation in Fairview while you’re at it, we can scope both at once. We serve all of Fairview.
Written by the team at Groundwork Construction Co.












