







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Allen, TX: What the Job Actually Involves
Door installation in Allen, TX typically runs $450 to $2,800 per door installed, with most exterior entry and patio door swaps landing between $900 and $2,200 depending on size, material, and whether the rough opening has to change. A standard replacement is a one-day job; a new opening in brick veneer or a door that requires framing changes runs two to three days. Call (844) 560-0925 and we’ll give you a written, line-item number before anyone touches the wall.

From Measure to Final Swing: How We Install a Door in Allen

Door work rewards planning and punishes shortcuts, so here’s the actual sequence we run, start to finish.
Stage 1 – Measure and confirm (day 1, about 60 to 90 minutes)
We measure the rough opening, check the wall for plumb and square, and confirm the swing direction and handing. You decide the door style, the material, the finish, and whether you’re keeping the existing trim or replacing it. On Allen brick-veneer homes, we also check for lintel condition and any prior water intrusion at the threshold, because that changes the install method.
Stage 2 – Order and lead time (typically 1 to 3 weeks)
Stock doors arrive fast; custom sizes, specialty glass, and certain wood species run longer. You sign off on the final spec sheet here, including hardware and threshold height. This is also where we confirm whether the job needs a permit pulled.
Stage 3 – Demo and prep (day 1 of install, 2 to 4 hours)
We pull the old door and frame, inspect the framing and sheathing for rot or insect damage, and repair anything soft before the new unit goes in. On slab-on-grade Allen homes, threshold reveals often turn up old termite damage or water staining that wasn’t visible from inside. We photograph anything we find and show you before we proceed.
Stage 4 – Set, shim, flash, and seal (day 1 or 2, 3 to 5 hours)
The new door goes in plumb and square, shimmed at the hinge points, fastened per manufacturer spec, and flashed and sealed at the exterior. This is the step that decides whether the door leaks in five years. We use proper sill pan flashing, not a bead of caulk and hope.
Stage 5 – Trim, hardware, and final adjust (day 2 or 3, 2 to 4 hours)
Interior and exterior trim go on, hardware installs, and we adjust the strike plate and hinges so the door swings clean and latches with light pressure. We walk the job with you, demonstrate the lock and any screen or storm door, and hand over the warranty in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
What You’ll Choose Between on a Door in Allen
The door itself is where most of the money and most of the regret live. Here’s how the real options shake out.
- Fiberglass entry doors – the workhorse for Allen. They don’t swell in humidity, hold paint and stain well, and take a hit from hail better than wood. Expect mid-range pricing and a long service life.
- Steel entry doors – strong, secure, and the most affordable of the three; they can dent under impact and need touching up if the finish chips.
- Solid wood doors – beautiful and heavy, but North Texas humidity swings mean seasonal swelling and sticking unless you stay on top of the finish.
- Patio and sliding glass doors – we install these as part of a full Windows & Doors in Allen scope, with tempered glass and a proper sill pan.
- Interior doors – hollow-core for closets and budget rooms, solid-core for bedrooms and bathrooms where privacy and sound matter.
- Hardware and thresholds – a quality lockset and a correctly set threshold do more for a door than an expensive slab. We won’t skimp here.
What Door Installation Costs in Allen, TX
Most single-door installations in Allen land between $450 and $2,800, with the bulk of exterior entry and patio door work in the $900 to $2,200 range. Here’s what pushes a job toward the low or high end.

- Size and type – a standard 36-inch entry door sits at the low end; a double door, a wide slider, or a custom-size unit climbs fast.
- Existing condition – rot, termite damage, or a wall that’s out of square adds demo, framing, and repair hours.
- Material grade – fiberglass and steel are the value picks; solid wood and custom glass land at the top.
- Opening changes – turning a window into a door or cutting a new opening in brick veneer means framing, header work, and patching.
- Permit scope – a straight replacement usually doesn’t need one; a new opening or structural change does, and that adds inspection time and a fee.
Your written estimate should list the door and hardware, demo, framing repair allowance, flashing and sealing, trim, and cleanup. It should also say plainly what’s excluded, like painting or masonry repair beyond the immediate opening. Our windows & doors service runs on upfront pricing, no surprises: the number you see is the number you pay, and we back the work with our 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Allen Homes Specifically Do to a Door Job
Allen grew from a small rural town into a Collin County suburb fast, and most of its housing stock sits in a 1990 to 2015 construction band. That means a lot of the doors we replace in 75013 and 75002 are original builder-grade units hitting the end of their life in the same few years. The bigger local factor is the black clay under our slab foundations: it swells in a wet spring and shrinks hard by August, and that movement shows up as doors that suddenly stick, won’t latch, or drag at the bottom. We see it in subdivisions off Exchange Parkway and along the US-75 corridor. Before we sell anyone a new door in Allen, we check whether the frame is out of square because the foundation has shifted, because a new door in a moving frame will stick too. If we find that, we’ll tell you. It’s part of being straight with you from the first visit.
Serving Allen, TX – Our Local Coverage Area
We serve Allen and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Allen

A standard door replacement in Allen is a one-day job, usually four to seven hours on site. Custom sizes, new openings, or jobs that uncover rot or foundation movement run two to three days. Call (844) 560-0925 for a firm timeline on your specific door.
Most straight replacement of an existing door in Allen doesn’t require a permit. Cutting a new opening or making a structural change does, and we pull it and pass inspection as part of the job. Codes shift, so we confirm the current requirement before work starts.
Yes, in most cases. Swapping a door in the same opening leaves the wall, plumbing, and framing untouched. Relocating a door or widening the opening means header and framing work, and that’s where the scope and cost grow.
Plan on $450 to $2,800 per door in Allen, with most entry and patio swaps between $900 and $2,200. Material, size, opening changes, and any repair uncovered during demo are the main variables. Call (844) 560-0925 for an exact quote; estimates are free.
Every door we install in Allen is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. We put that in writing, along with the manufacturer’s product warranty. If a door sticks or a seal fails inside that window, we come back.
Ready for a Door That Swings Right?
If you’re pricing door installation in Allen, start with a free on-site estimate. We’ll measure the opening, walk through the material and hardware choices, flag anything the foundation or framing might be doing to the frame, and hand you a written, line-item quote. No pressure, no surprise line items. Homeowners often pair new doors with Cabinets & Countertops in Allen or a Garage Conversion ADU in Allen, and we can scope those together. Call (844) 560-0925 to schedule, and a real person answers, any hour.
Written by the team at Groundwork Construction Co.












