







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Farmers Branch, TX: What It Takes and What It Costs
Door installation in Farmers Branch typically runs $450 to $1,900 per door for an exterior entry or patio door, with interior doors landing between $250 and $700 each installed. A standard exterior door swap takes one long day; a door that requires reframing, a new threshold, or a widened opening stretches to two or three. On the acreage-and-infill lots around 75234, oversized and heavy-duty doors are common, and they take longer. Call (844) 560-0925 for a free on-site estimate.

How Door Installation Works: The Sequence We Follow

Every door install follows the same five stages. Here’s what actually happens, when, and what you decide at each point.
Stage 1: Measure and site check (about 45 minutes)
We measure the rough opening, check the frame for square and plumb, and look at the sill and threshold condition. On older Farmers Branch ranches, this is where we find the surprises: a slab that’s settled half an inch, or a frame that’s racked from clay-soil movement. You decide the door style and swing direction at this visit so the order goes in.
Stage 2: Order and lead time (10 to 21 days)
Stock sizes ship faster. A custom-width door for a detached workshop or an oversized entry arrives in two to three weeks. This is the stage where homeowners most often change their mind on material, so we lock the spec in writing before the order places.
Stage 3: Demo and prep (2 to 4 hours per door)
Old door comes out, the opening gets cleaned back to solid framing, and any rot in the sill or jack studs gets cut out and replaced. We don’t skip this step. A new door slapped onto a soft or wet sill fails within two seasons in North Texas.
Stage 4: Set, shim, and seal (3 to 5 hours per door)
The door goes in, gets shimmed plumb, and is fastened through the frame per manufacturer spec. Flashing goes on the exterior, then foam or backer and sealant. Hardware and lockset land last. This is where weather-tightness is won or lost, especially on west- and south-facing doors that take the summer sun.
Stage 5: Adjust and walk through (about 30 minutes)
We cycle the door a dozen times, adjust the strike plate and hinges, and check the latch and deadbolt alignment. Then we walk it with you. The 730-Day Done Right Promise covers workmanship from that walkthrough forward, so anything that shifts later gets made right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Door Options You’ll Actually Choose Between
Most of the decision comes down to four choices: material, core, glazing, and hardware. Here’s the honest read on each.
- Fiberglass entry doors: $600 to $1,400 for the slab. They resist the swelling and warping that wood deals with in Texas humidity, hold paint well, and suit the post-war ranch stock on most Farmers Branch streets. Best all-around pick for an exterior door.
- Steel doors: $400 to $1,000. Strong and budget-friendly, but they dent and can rust at the bottom edge if water pools at the threshold. Fine for a side or garage-adjacent door.
- Solid wood doors: $800 to $2,500. Beautiful, and the right call for a front entry with curb-appeal weight. They need a good overhang or storm protection or they’ll move with the seasons.
- Insulated cores and multi-point glazing: add $150 to $500 per door. Worth it on doors facing the afternoon sun or on any oversized opening.
- Heavy-duty hardware and oversized hinges: $100 to $400. On the big workshop and barn-style doors common to larger lots, this isn’t optional. Standard hinges sag under the weight.
What Door Installation Costs in Farmers Branch, TX
Expect $450 to $1,900 per exterior door installed, $250 to $700 per interior door, and $900 to $2,600 for a patio or oversized workshop door that needs heavier framing and hardware. The low end is a stock fiberglass door dropped into a sound existing frame. The high end is a custom-width heavy door on a lot where the opening needs rebuilding.
Four things push a job up or down:

- Opening condition. A square, solid frame keeps you near the floor of the range. Rotted sill, racked framing, or a settled slab adds $200 to $800 in carpentry.
- Door size and weight. Oversized and heavy-duty doors on detached workshops and acreage properties need engineered framing and commercial-grade hinges. That’s where most of the high-end numbers come from.
- Glass and finish. A plain slab is one price; a leaded-glass entry or a factory-stained custom finish is another.
- Whether the opening moves. Widening a doorway pulls in framing, drywall, trim, and possibly a header. That’s a different job with a different number.
A written estimate from us lists the door, hardware, labor, disposal of the old door, and any carpentry, line by line. It also states what’s excluded: paint touch-up beyond the trim, and any permit fee if the scope triggers one. Upfront pricing, no surprises. Estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Farmers Branch Homes Do to This Job
The housing stock here does most of the talking. Most of 75234 is post-war ranch and mid-century single-family housing from the 1950s through the 1970s, and the door openings on those homes have been through sixty-plus years of North Texas black-clay soil swelling and shrinking. We routinely pull a door and find the frame out of square by half an inch or more, or a sill that’s gone soft from years of splash-back. That’s a carpentry repair before the install starts, and it’s why we never quote a door over the phone without looking.
Farmers Branch is essentially built out, so what we work on is remodel-of-existing and tear-down-and-rebuild, not new construction. On the older streets the original one-story ranches are being replaced by two-story infills squeezed onto the same lot, which means tight staging, alley access, and mature-tree protection shape how we run a crew here. All of it falls under City of Farmers Branch permitting and inspection, and homeowners inside the loop expect the paperwork handled precisely. When a door install is part of a full Windows & Doors in Farmers Branch scope, that coordination matters even more – it’s one inspection path, not two.
Two things come up on almost every job in this ZIP. Hail and high-wind events drive exterior rebuild demand, so a damaged entry or storm door often arrives in the same visit as roof and exterior work. And on larger lots with detached workshops, the doors are oversized and heavy, which means heavier-duty openers, springs, and hinges. If you’re pairing a door project with interior work, homeowners often pair this with Cabinets & Countertops in Farmers Branch or a Garage Conversion ADU in Farmers Branch when the garage door set is getting revisited as part of the build. Our Windows & Doors service covers the full exterior opening, and our crews cover all of Farmers Branch and the surrounding area.
Serving Farmers Branch, TX – Our Local Coverage Area
We serve Farmers Branch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Farmers Branch

A standard exterior or interior door installs in one day. Custom widths, reframing, or an oversized workshop door takes two to three days once the door is on site, plus a 10 to 21 day lead time on the order. Call (844) 560-0925 for an exact timeline on your door.
A like-for-like replacement in the same opening usually doesn’t require a permit. Widening an opening, adding a new exterior door where there wasn’t one, or structural changes do trigger City of Farmers Branch permitting and inspection. We tell you which category your job falls into before the work starts and pull the permit when it’s needed.
In most cases, yes. A same-size door swap doesn’t touch plumbing or structure at all. If the job calls for widening an opening or moving a door to a new wall, that changes the scope and we say so in the estimate. Estimates are free and the answer is in writing before you commit.
Exterior doors run $450 to $1,900 installed, interior doors $250 to $700, and oversized or patio doors $900 to $2,600. The biggest variable is the condition of the existing opening. Call (844) 560-0925 for an exact quote; the estimate is free and line-itemized.
Every door we install is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right. The manufacturer’s warranty covers the door itself; ours covers the workmanship, and both are documented in your estimate.
Get a Free Door Installation Estimate in Farmers Branch
Call (844) 560-0925 to schedule a free on-site estimate for door installation in Farmers Branch. We’ll measure the opening, check the frame and sill condition, and hand you a written line-item quote with the door, hardware, labor, and any carpentry spelled out. Calls are answered by a live person, 24/7. If the job qualifies, you’ll also hear about our current $1,000 off projects over $10,000 and 0% financing for 18 months. No pressure, no surprises.
Written by the team at Groundwork Construction Co.












