







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Richardson, TX: What It Costs and How Fast It Goes In
A chain link fence in Richardson typically runs $3500 – $9000 for a standard residential lot line, and most jobs are finished in two to three working days once we’ve marked utilities and pulled the permit. You’re paying for galvanized posts set in concrete, tension wire, and fabric that holds its shape through North Texas wind instead of sagging by year three. Call (844) 560-0925 and we’ll walk your property line and give you a written, line-item estimate.

How a Chain Link Fence Goes In, Stage by Stage

Chain link looks simple from the street. The difference between a fence that’s still tight after a decade of spring storms and one that’s leaning by year four is entirely in the prep. Here’s the sequence we follow on a Richardson job, with the real timing.
Stage 1: On-site measure and layout (day 1, about an hour)
We walk the property with you, confirm the actual lot line against your survey, and mark where posts land, where gates sit, and where the fence meets the house. You decide two things here: gate count and swing direction. Everything else flows from that.
Stage 2: Utility locate (48 to 72 hours before digging)
Texas law requires a locate call before anyone puts a shovel in the ground, and it’s not optional. This is the buffer we build into the schedule. It takes the wait out of the timeline and keeps us off your gas, water, and electrical lines. This step happens on every job, no exceptions.
Stage 3: Demo and post setting (day 2, most of the day)
Old fencing comes out and hauls off. Terminal posts (corners, ends, gates) get set deeper and with more concrete than line posts because that’s where wind load concentrates. Posts set in a concrete collar and left to cure are what keep the whole run rigid. We don’t rush this step.
Stage 4: Rails, tension wire, and fabric (day 3, morning)
Top rail goes in, tension wire gets stretched along the bottom, and the fabric is pulled and tied. A proper stretch is where the quality shows: fabric that’s been pulled to spec sits flat and resists sagging, while a lazy install leaves ripples that catch the wind and flap. We walk the run with you and check every tie before we call it done.
Stage 5: Gate hang and final walkthrough (day 3, afternoon)
Gates go on their hinges, get adjusted for a clean swing, and we walk the whole line with you. This is where you inspect it too. Any punch-list item gets handled before we leave, and the workmanship is covered under the 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Options You’ll Actually Choose Between
Chain link isn’t one product. The decisions below are the ones that move both the price and how the finished fence looks and lasts.
- Fabric gauge. Residential grade is typically 11.5 gauge; heavier 9 gauge costs more but resists bending and holds up far better where kids, dogs, or storm debris put pressure on it. Ask which gauge you’re being quoted. A cheap price often means thinner fabric.
- Coating. Galvanized steel is the budget choice and still performs well in dry conditions. Vinyl-coated (usually black or green) costs more up front but looks sharper from the street and takes the summer heat and sun exposure with less wear on the surface.
- Height. Four-foot is the common residential run. Five and six foot cost more in material and gate hardware but suit a property with a pool or a dog that needs the extra height. HOAs in the area often cap height, so check before you commit.
- Post and gate framing. Standard residential posts are fine for a flat lot line; heavier-wall posts and stronger gate frames are worth the upgrade where gates get daily use or a run spans a long distance between corners.
- Top rail and tension wire. A top rail and bottom tension wire together keep fabric stretched and weighted correctly. Skipping the tension wire saves a little money and costs you a fence that sags sooner.
- Gates and hardware. Walk gates, drive gates, and self-closing hinges for a pool are all separate choices. Gate hardware is where cheap installs cut corners first, so ask what’s going on the hinges.
What a Chain Link Fence Costs in Richardson, TX
For a typical residential lot, Richardson chain link fencing lands in the $3500 – $9000 range. The low end is a straightforward run of galvanized 4-foot fence with standard posts and one walk gate. The high end is a larger perimeter with vinyl coating, heavier fabric, a drive gate, and a yard that’s harder to work in.
What moves the number:

- Total linear feet. This is the biggest lever. Price is largely driven by footage plus corner and gate count.
- Existing fence removal. Tearing out an old run and hauling it off adds labor and disposal cost. A clean, demo-free lot sits lower.
- Lot conditions. Sloped ground, tight side yards, and mature trees along the line all slow down post setting and add cost. Rocky or heavily compacted ground can affect digging time.
- Material grade. Galvanized at 11.5 gauge on the low end; vinyl-coated, heavier gauge, and 5 or 6 foot on the high end.
- Gates. A drive gate or several walk gates raises hardware and framing cost.
A written estimate from us breaks these out line by line: footage, gauge, coating, post count, gates, demo, and permit. What’s typically not included is anything a hidden condition reveals (like an unexpected obstruction in a post hole) and any landscaping repair around the posts. We flag those possibilities up front rather than surprising you later. Call (844) 560-0925 for an exact number on your lot.
See the difference
Before
After
Before
After
Before
AfterWhat Richardson Homes Specifically Do to This Job
Richardson is built out, and that shapes every fence job here. Much of the 75080 and 75081 core is 1955 – 1975 brick-veneer ranch and split-level housing on slabs, so we’re almost always working on an established lot line with a mature tree or an old fence already in the way rather than a fresh subdivision. That means demo is more common, and post placement sometimes runs into roots or the buried utilities of a 60-year-old lot. The caliche clay under a lot of Richardson makes digging slower than it looks, and the same clay movement that stresses foundations can shift a post if it isn’t set properly.
The storms matter too. Hail and severe spring weather come through regularly, and a fence that’s been stretched tight with proper tension holds up to wind far better than a loose one. Because of the tear-down-and-rebuild cycle in the older core, we also routinely set fence lines against new-construction lots next door, where survey and drainage lines need to be respected. If a build-out or accessory structure is part of the same project, homeowners often pair this with ADU Site Prep & Utilities in Richardson and a Door Installation in Richardson to complete the exterior. As part of a broader yard rebuild, a chain link perimeter is often the first piece of a full Fence Installation in Richardson project. We cover the whole Richardson area, including 75080, 75081, and 75082, and when you’re ready to expand the job, our Fence Installation service covers the rest.
Serving Richardson, TX – Our Local Coverage Area
We serve Richardson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Chain Link Fence in Richardson

Most residential chain link runs are finished in two to three working days, not counting the 48 to 72 hours the utility locate takes before we can dig. The locate wait is required and runs in the background, so the working days on site are usually two or three. Call (844) 560-0925 to get a firm timeline on your lot.
It depends on the height and location, and the rules are set locally. Fences above a certain height, or near a corner or easement, typically require a permit, and HOA rules can add their own limits on height and material. We check the requirements for your address and pull permits where needed so your fence passes inspection. Call (844) 560-0925 and we’ll sort it out.
Yes. The utility locate in Stage 2 marks where lines run, and we set posts to avoid them or hand-dig where we need to work close. Established Richardson lots with older buried lines are exactly why we don’t skip the locate. If something is in the way, we show you before we change the plan. Call (844) 560-0925 to talk through your yard.
Plan on $3500 – $9000 for a standard residential chain link fence, with the number driven by footage, material grade, gates, and how much old fence has to come out. Vinyl-coated, heavier gauge, and larger perimeters push toward the top. Call (844) 560-0925 for a written line-item quote – the estimate is free and the price doesn’t change once work starts.
Every chain link fence we build is covered by the 730-Day Done Right Promise: if it’s not done right, we make it right. That covers the workmanship on posts, framing, and gates for the full period. Call (844) 560-0925 and we’ll explain exactly what that means for your fence.
Get a Free Chain Link Fence Estimate in Richardson
If you’re fencing in a yard in Richardson, the fastest way to a real number is a call. We’ll take your address, ask about footage and any old fence you want gone, and set a time to walk the property. You get a written, line-item estimate and a clear start date. Upfront pricing, no surprises, and live people answer the phone around the clock. Call (844) 560-0925 to schedule your free estimate.
Written by the team at Groundwork Construction Co.












