







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Dallas, TX: What It Actually Involves
Door installation in Dallas, TX typically runs $450 to $2,200 per door installed, depending on whether it’s a single interior slab swap or a full exterior entry system with new framing, weather sealing, and hardware. Most single-door jobs close out in one day; whole-house packages of six to ten doors usually take two to four working days. Call (844) 560-0925 for a free on-site estimate and we’ll give you a written, line-item number before anyone touches a hinge.

How We Run a Door Installation Job, Stage by Stage

Door work looks simple until you’re standing in a 1940s East Dallas bungalow and the rough opening is out of square by three-quarters of an inch. Here’s the actual sequence we follow, and where you make the calls.
Stage 1: Measure and confirm the opening (day 1, about an hour)
We measure the rough opening, check the jamb for plumb and level, and note whether the existing frame is sound enough to reuse or needs to come out. On pier-and-beam homes we also look at the floor at the threshold. A door that sticks or drags in Oak Cliff is often a floor issue, not a door issue, and it makes no sense to hang a new slab over a sagging subfloor. You decide here whether you’re keeping the existing frame or going with a pre-hung unit.
Stage 2: Tear-out and prep (2 to 4 hours per door)
Old door and hardware come out, trim is carefully removed so it can be reused where possible, and the opening gets squared and shimmed. If we find rot at the sill or water damage behind exterior brick molding, we stop and show you photos before doing anything else. That’s a change order conversation, and we’d rather have it while the wall is open than after.
Stage 3: Set the unit and shim (2 to 3 hours per door)
The new door goes in, gets shimmed at the hinges and lock side, and is checked for a consistent gap all the way around. Exterior doors get set with a slight bevel toward the sill so water sheds the way it should. This is the stage where sloppy work shows up six months later as a draft or a door that won’t latch.
Stage 4: Insulate, seal, and trim (1 to 2 hours per door)
We foam the gap between the frame and the rough opening, then reinstall or replace the casing and add new weatherstripping and a sweep on any exterior unit. This is also where you pick your hardware finish, hinge color, and whether you want a keyed-alike setup on multiple entries.
Stage 5: Field check and walkthrough (about 30 minutes)
We open and close every door a dozen times, check the latch, check the deadbolt alignment, and look for daylight around the perimeter of exterior doors. You walk it with us before we leave. Any adjustment needed after that is covered under our 730-Day Done Right Promise – if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between in Dallas
Most of the decisions on a door installation come down to four things. Here’s the honest trade-off on each.
- Interior slab vs. pre-hung unit. A slab (just the door) is cheaper and works if the existing frame is solid. A pre-hung unit includes the frame and is the safer call on older homes where the jamb has shifted. Pre-hung costs more but saves you labor on squaring.
- Hollow-core vs. solid-core interior doors. Hollow-core is light, inexpensive, and fine for closets and bedrooms nobody slams. Solid-core costs roughly double and cuts sound transfer noticeably, which matters if you’re working near a home office or a nursery.
- Exterior door material. Fiberglass holds up best against Dallas sun and resists dents and rot. Steel is strong and takes paint well but can dent. Wood looks best and needs the most maintenance in our heat and humidity swings. You’ll see fiberglass entry systems from brands like Therma-Tru as a common middle path.
- Hardware and finish. Satin nickel and matte black are the two finishes we install most in Dallas. A keyed-alike set across the front, back, and garage entry saves you a keychain headache. Grohe makes a solid line of entry hardware if you want it matched to fixtures elsewhere in the house.
- Energy spec on exterior units. Low-E glass and a good thermal break matter more than most people expect on a west-facing door. It’s a modest upcharge that pays back on summer cooling.
What Door Installation Costs in Dallas, TX
For a single door, plan on $450 to $2,200 installed. A whole-house package of eight interior doors plus one exterior entry typically lands between $4,000 and $9,000. Those numbers move based on five things:

- Door count and type mix. Interior slabs are the cheapest per unit; exterior entries with sidelights and hardware are the most expensive.
- Condition of the existing opening. A straight, sound frame is a one-day job. Rotted sills, out-of-square openings, or hidden water damage add framing labor.
- Whether the frame is reused. Pre-hung units cost more in materials but less in labor. On older pier-and-beam homes, pre-hung is usually the better value.
- Material grade. Hollow-core to solid-core, steel to fiberglass, builder-grade hardware to a keyed-alike set. Each step up is a real jump.
- Permit and inspection scope. Swapping a door in an existing opening rarely needs a permit. Cutting a new opening in an exterior wall does, and that adds both cost and inspection time.
A written estimate from us lists doors, hardware, trim, sealant, labor, and disposal as separate lines. What it won’t include without a conversation: structural framing changes, drywall repair beyond minor patching, and painting. We tell you that up front so there’s no surprise on the invoice – the number you see is the number you pay. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off.
See the difference
Before
After
Before
After
Before
AfterWhat Dallas Homes Specifically Do to a Door Installation
Our region’s expansive black-clay soil is the single biggest thing that separates a Dallas door installation from the same job in San Antonio or Austin. That clay swells and shrinks with the wet-dry cycle, and after a dry Texas summer it shrinks and cracks open, then the fall rains push it back up. The result is that foundation cracks and sticking doors show up in clusters, and we routinely check the pier-and-beam bungalows in East Dallas and Oak Cliff for sagging floors before we sign off on anything. We cover these neighborhoods and the 75379, 75380, 75381, and 75382 ZIP codes across Dallas, plus Highland Park and University Park nearby. Housing stock here runs from 1920s-40s pier-and-beam to 1950s-70s shallow-slab ranch homes to new infill townhomes, sometimes on the same block, so no two openings measure the same. If the wider project includes window work, that’s usually part of a full Windows & Doors in Dallas scope, and our Windows & Doors service handles the whole envelope. Homeowners often pair a door refresh with Cabinets & Countertops in Dallas when they’re updating an adjacent kitchen, or with a Garage Conversion ADU in Dallas where a new exterior entry is part of the plan.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Dallas

A single door takes half a day to one full day. Whole-house packages of six to ten doors run two to four working days. Pre-hung units on a sound frame go faster than slab swaps on older pier-and-beam homes where the opening needs squaring. Call (844) 560-0925 and we’ll give you a realistic schedule with your free estimate.
Replacing a door in an existing opening usually doesn’t require a permit. Cutting a new opening in an exterior wall does, and it triggers an inspection. We tell you which side of that line your job falls on before any work starts. Call for a free on-site assessment if you’re unsure.
In most cases, yes. Swapping a door in an existing opening doesn’t require touching plumbing or structure. The exceptions are doors in load-bearing walls or openings where the frame has rotted – those need framing repair, and we’ll flag it before the job begins.
Single doors run $450 to $2,200 installed, and a full-house package of eight interior doors plus an exterior entry lands between $4,000 and $9,000. Material grade, frame condition, and whether the opening needs repair are the main drivers. Call (844) 560-0925 for an exact quote – estimates are free.
Every door installation we do is backed by our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship on hanging, shimming, sealing, and hardware installation. Manufacturer warranties on the doors and hardware apply separately.
Ready for a Free Door Installation Estimate in Dallas?
If you’re planning door installation in Dallas, the next step is simple: call (844) 560-0925 and we’ll schedule a free on-site estimate. A real person answers, 24/7 – no voicemail, no waiting until Monday. We’ll measure your openings, walk the options with you, and hand you a written, line-item quote with a fixed number. Our technicians have up to 12 years of experience and arrive background-checked and in uniform.
Written by the team at Groundwork Construction Co.












