







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Frisco, TX: What It Takes and What It Costs
Concrete driveways & concrete work in Frisco, TX typically run $4,500 – $12,000 for a new driveway pour and $5,000 – $14,000 for a full tear-out and replacement, with most residential jobs finished in 3 to 5 working days of on-site labor plus a 7-day cure before you park on it. A standard two-car apron and approach falls at the low-to-mid end; a three-car drive with a widened approach, decorative finish, or a slope correction pushes toward the top. Call (844) 560-0925 and we’ll walk your property and put a firm written number in front of you.

How we build it: the five stages from bare dirt to a cured slab

Concrete is unforgiving about sequencing. Get the subgrade wrong and the prettiest finish in Frisco will crack in two winters. Here’s exactly what happens on your job and when you’ll be asked to make a call.
Stage 1 – Site walk and layout (Day 1, morning)
We mark the footprint, confirm setbacks against your plat, and check where the driveway meets the street apron and the garage slab. This is where you decide width and whether we’re tying into an existing approach or cutting a new one. If your lot has an HOA, the approved architectural submittal should already be in hand before we chalk a line – more on that below.
Stage 2 – Demo and haul-off (Day 1, most of the day)
Old slab comes out with a breaker, rebar gets cut and hauled, and we strip the subgrade down past the root zone. On a typical Frisco tear-out this is one long day with a dumpster staged in the street. You’ll want cars out of the garage the night before.
Stage 3 – Subgrade, base, and forms (Days 2 – 3)
We compact the base in lifts, set forms to finished grade, and establish the slope away from the garage. North Texas clay is the whole story here: expansive soil that swells when wet and shrinks when dry will move a slab that isn’t built for it. That means proper base depth, a vapor barrier, and a reinforcement schedule set before any mud shows up.
Stage 4 – Reinforcement and pour (Day 3 or 4)
Rebar or mesh goes in on chairs so it sits mid-slab, not on the dirt where it does nothing. Then the pour, screed, float, and the finish you chose. You decide the finish at the estimate, not on pour day – changing your mind mid-pour costs money and time.
Stage 5 – Cure, control joints, and walkthrough (Days 4 – 11)
Control joints get cut within the first 24 hours while the concrete is still green. We keep traffic off for 7 days minimum and heavy vehicles off for 10. Then a walkthrough where we hand you the care sheet and log the finish under our 730-Day Done Right Promise – if a joint spalls or a panel heaves, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between
Concrete driveway work in Frisco isn’t one product. Here’s what the choice list looks like and where each one honestly lands.
- Standard broom finish – the default for a reason. Best traction in rain, lowest cost, holds up to Texas sun. It’s the finish most subdivision HOAs already have on file as approved.
- Exposed aggregate – more texture and visual interest, hides tire marks better, but costs more and is harder to patch invisibly later if a panel ever needs replacing.
- Integral color – pigment mixed into the batch rather than spread on top, so it won’t wear through. Adds a modest premium and reads as a deliberate upgrade next to builder-grade gray.
- Standard 4-inch slab vs. thickened edges – a 4-inch field with 6-to-8-inch thickened edges at the apron and garage is the right call for most residential drives. Full 6-inch slabs cost more but suit heavy trucks, RV pads, or commercial-adjacent use.
- Rebar vs. welded wire mesh – rebar on chairs is the stronger, more consistent choice on clay. Mesh is cheaper and adequate for light foot-traffic paths, less so for a drive carrying two SUVs.
Finish and reinforcement also set how the driveway ties into the rest of the hardscape. If you’re resurfacing the drive and redoing the front walk at the same time, that’s part of Driveway & Pavers in Frisco and worth pricing together so the elevations match at the door thresholds.
What Concrete Driveways & Concrete Work costs in Frisco, TX
Here’s the honest range, then the levers that move you up or down it.

| Line item | Typical range |
|---|---|
| New concrete driveway installation | $4,500 – $12,000 |
| Full driveway replacement (demo + pour) | $5,000 – $14,000 |
Five variables drive where your number lands:
- Square footage and width. A single-car apron and a three-car drive with a widened street approach aren’t the same job. Most of the spread between $4,500 and $12,000 lives here.
- Demo and haul-off. Breaking out an existing slab, cutting rebar, and paying dump fees is real money. A replacement always costs more than a fresh pour over prepared ground.
- Subgrade condition. Fill dirt, tree roots, or a soft spot under the slab means excavation and re-compaction before you pour. Cheap now, expensive later.
- Finish and reinforcement grade. Broom and mesh is the floor; exposed aggregate, integral color, and full rebar move you up the range.
- Permit and inspection scope. A new approach that touches the right-of-way pulls in city review on top of the standard residential permit.
A written estimate from us is line-itemed: demo, base, reinforcement, concrete volume, finish, permit, and haul-off, each with a number. No-hassle upfront pricing means the number you see is the number you pay – no change orders sneaking in mid-job. What’s typically not included: landscape repair around the edges, driveway gates, and any drainage work beyond the driveway footprint.
See the difference
Before
After
Before
After
Before
AfterWhat Frisco homes specifically do to this job
Frisco is one of the fastest-growing large cities in the country, and nearly all of its built environment went up after the 1990s. That single fact changes concrete work here. We’re rarely tearing out 40-year-old slabs; we’re replacing builder-grade driveways that are 15 to 25 years old across subdivisions like Newman Village and the neighborhoods off Teel Parkway and Main Street, or pouring new ones on infill lots and additions. North Texas clay soil is the recurring villain – it swells and shrinks with every wet-dry cycle, and a driveway poured without a proper base and reinforcement will crack and settle in ways a homeowner sees within a couple of seasons. Practically every newer subdivision here is HOA-governed, so the finish, color, and even the driveway width often need architectural approval on top of the city permit, and a crew that skips that step derails the whole schedule. When you’re rebuilding the approach and the front of the house at the same time, homeowners often pair this with Door Installation in Frisco so the entry, threshold, and drive all land at the same elevation. We cover Frisco and the surrounding ZIPs 75034, 75035, and 75033.
Serving Frisco, TX – Our Local Coverage Area
We serve Frisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Concrete Driveways & Concrete Work in Frisco

Most residential jobs run 3 to 5 working days on site plus a 7-day cure before you drive on it. Larger tear-outs, tight lot access, or HOA-driven scheduling can stretch that to 6 or 7 days. Call (844) 560-0925 for a timeline specific to your property.
Yes, most new driveways and any work touching the street approach require a city permit and inspection. We pull the permit and manage the inspections as part of the job. If your lot is in an HOA, architectural approval is a separate step we’ll walk you through before demo day.
In the overwhelming majority of cases, yes. A driveway is surface and subgrade work and doesn’t touch plumbing or framing unless the layout changes. If you’re adding a wider approach or a new pad for an outbuilding, that’s when we scope utilities – and if it’s an ADU pad, homeowners often pair this with ADU Site Prep & Utilities in Frisco.
Installation runs $4,500 – $12,000 and a full replacement runs $5,000 – $14,000, with size, demo, subgrade, finish, and permit scope deciding where you land. Call (844) 560-0925 for an exact quote – estimates are free.
Every job is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If something isn’t right, we come back and make it right. Our technicians carry up to 12 years of experience, and every one of them is background-checked and arrives in uniform.
Get a free on-site estimate for concrete driveways & concrete work in Frisco
Call (844) 560-0925 and you’ll reach a live person, day or night – no voicemail, no waiting until Monday. We’ll schedule a free on-site estimate, walk your property, and hand you a line-itemed written quote with the finish, reinforcement, and permit scope spelled out. Financing is available at 0% for 18 months, and projects over $10,000 take $1,000 off. Whether it’s a cracked builder-grade slab or a brand-new pour on an infill lot, this is our Driveway & Pavers work done right and backed in writing. Reach out today and let’s get a number on your driveway.
Written by the team at Groundwork Construction Co.












