







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Dallas, TX: What to Expect Before You Call
A chain link fence in Dallas usually runs $3500 – $9000 installed, with most residential jobs landing around $22 – $38 per linear foot. Plan on two to four working days on site for a typical backyard run, longer if you’re fencing a full lot with gates. The number that actually matters is wind load, and that’s what we build around here. Call (844) 560-0925 for a free on-site estimate.

How a Chain Link Fence Goes Up, Stage by Stage

We don’t quote blind. The first thing we do is walk the property line with you and decide where the fence actually sits. That matters in Dallas more than in most places, because property lines in older neighborhoods don’t always match what the county shows. If a survey is fuzzy, you’ll want it sorted before we dig.
Stage 1: Layout and utility locate (day one, half a day)
We stake the run, confirm heights and gate placements with you, and call for utility locates. You approve the final line on paper before anything gets broken. If you’re fencing near a pool or an accessory structure, that’s when we flag setbacks.
Stage 2: Tear-out and grading (day one to day two)
If there’s an old fence, we remove it and haul it off. More often in Dallas, we’re dealing with posts that have heaved or tilted. We pull them, then grade and level the line so panels hang straight and don’t sit in ponding water. Expect four to six hours for a standard residential run.
Stage 3: Setting posts in concrete (day two)
This is the part that decides whether your fence survives the next north Texas wind event. We set line, corner and gate posts in concrete at the correct depth, with terminal posts anchored deep because they carry the tension. The concrete needs to cure before we pull anything tight. You’ll make your call on post spacing here.
Stage 4: Rails, mesh and tension (day three)
Top rail goes in, mesh gets stretched and tied off, and gate hardware goes on. We tension to spec so the fabric doesn’t sag. This is where a cheap install and a good one look different within a year.
Stage 5: Walkthrough and cleanup (day three to day four)
We walk the whole fence with you, check gates for swing and latch, confirm tension, and pull all debris and excess concrete. You sign off, and the 730-Day Done Right Promise covers the workmanship from that day.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Chain link isn’t one product. The spec sheet is where most of your money gets decided, so here’s the honest trade-off on each piece.
- Gauge of mesh: 11.5-gauge is common and affordable. 9-gauge is heavier and resists bending, denting and wind fatigue far better. For anything facing open ground or a busy alley, we steer you to 9-gauge.
- Coating: Galvanized lasts well in most conditions. Vinyl-coated (usually black or green) costs more but blends into landscaping and adds a layer against corrosion. In north Texas sun and occasional hard freezes, the vinyl coat earns its keep on appearance alone.
- Height: 4-foot is standard residential. 6-foot gives more privacy screening and better wind performance on exposed lots. Anything taller than 6 feet in a residential zone may need a permit or a variance; we check before we quote.
- Gates: Walk gates and drive gates differ a lot in price, mostly because drive gates need heavier frames and better hardware. We size the frame to the opening so it doesn’t sag.
- Post spacing: Tighter spacing costs more in materials and labor but stiffens the fence. On wind-exposed lots, it’s the difference between a fence that stands and one that leans after a spring squall.
For the rest of the yard work around a fence, most homeowners plan the whole run as part of a fuller outdoor scope; that’s a conversation for our Fence Installation in Dallas service, which handles the full project beyond chain link alone.
What Chain Link Fence Costs in Dallas, TX
Installed residential chain link in Dallas runs $3500 – $9000, with the bulk of jobs landing in the middle. Here’s how the line items break down so you can see where the number comes from.

| Item | Typical Dallas range |
|---|---|
| Standard 4-ft chain link, per linear foot | $18 – $28 |
| Heavier 6-ft with 9-gauge mesh, per linear foot | $28 – $38 |
| Walk gate (installed) | $250 – $550 |
| Drive gate (installed) | $600 – $1,800 |
| Old fence tear-out and haul-off | $300 – $900 |
| Full residential job, all in | $3500 – $9000 |
What pushes a job to the high end: longer runs, tighter post spacing for wind exposure, heavier gauge, a drive gate, and tear-out of an old fence. What keeps it lower: short runs, standard 4-foot height, and no removal. We quote upfront, line by line, and the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Dallas Homes Do to This Fence Job
Dallas sits on expansive black-clay soil that swells when it’s wet and shrinks hard when it’s dry. That clay cycle is the single biggest thing that changes a fence install here compared to sandier Texas metros. After a dry summer the ground pulls away from post holes and posts loosen; then the fall rains swell it back and push everything around. We set posts deeper and use proper concrete anchoring to ride that cycle out, and we check for existing heave before we quote.
The housing stock matters too. In East Dallas and Oak Cliff you’ve got 1920s – 40s pier-and-beam bungalows with mature trees and roots that make digging interesting. Out toward the infill and rebuild pockets, you’re fencing brand-new lots with fresh grading that hasn’t settled yet. We work across ZIP codes 75379, 75380, 75381 and 75382 and adjust the approach to each lot. If you’re grading or prepping utilities on a new build, homeowners often pair a fence with ADU Site Prep & Utilities in Dallas to get the site work done in one pass. Permits and inspections, where a job needs them, get pulled and passed before we call it done.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked, Chain Link Fence in Dallas

Most residential chain link jobs here finish in two to four working days once we start. A short run with a single walk gate can be done in two; a full-lot install with a drive gate and old-fence tear-out runs closer to four. Schedule and weather can shift it, so we confirm dates before we begin.
It depends on height and where the fence sits. Standard residential heights often don’t require one, but taller fences and some corner or setback situations do. We check the requirement for your specific lot before we quote, and we pull and pass any permit the job needs.
Expect $3500 – $9000 installed, driven mostly by linear footage, gauge, height and gate count. Call (844) 560-0925 for an exact quote; estimates are free and itemized.
No, not when we’ve done the walk-through right. We price the fence we can see and the subgrade we can inspect. If we hit something buried we couldn’t reasonably foresee, we stop and talk to you before anything changes. Otherwise the written number stands.
Every chain link install is backed by our 730-Day Done Right Promise. If the workmanship fails within that window, we make it right. Hardware and material warranties come from the manufacturers and vary by component.
If you’re weighing the whole outdoor plan alongside this, our Fence Installation service covers the broader scope, and for exterior doors that pair with a yard project, see Door Installation in Dallas. We cover Dallas and the surrounding area, including Highland Park, University Park, Farmers Branch and Garland.
Get a Free Chain Link Fence Estimate in Dallas
We’ll walk your property line, check the grade and soil conditions, and hand you a line-item written estimate for a chain link fence in Dallas. No pressure, no vague numbers. Call (844) 560-0925 and a live person answers around the clock to get you scheduled. Financing is available at 0%, and projects over $10,000 get $1,000 off.
Written by the team at Groundwork Construction Co.












